Tips for stretching piercings and measuring earlobes
Lifestyle Fashion admin  

Tips for stretching piercings and measuring earlobes

The following tips on how to stretch piercings are specifically geared towards measuring earlobes, where earlobe piercings can be enlarged to very large sizes to incorporate many different types of ear jewelry, including impressive flesh tunnels. .

Stretching piercings have been popular in many civilizations throughout history, taking many forms, from measuring earlobes to stretching labret and septum piercings. In the earliest periods of history, the materials used were wood, stone, bone, horn, shells, claws, and claws, molded and carved to make it easier for the piercings to stretch.

The earliest known incidence of humans measuring earlobes was discovered in 1991, on a glacier in the Otztal Alps between Italy and Austria, where a 5,300-year-old mummified body with tattoos and an earlobe piercing was found. the ear between 7 mm and 11 mm in diameter. Although the method used was definitely known, this may have been accomplished by a method known as dead stretching, in which gradually larger ear jewelery is forced through the gradually increasing diameter hole.

Preparation

In preparation for the measurement, make sure you have a good fragrance-free antibacterial soap. Next, you will need a sea salt solution; prepare it with three tablespoons of salt in enough water to dissolve it, and at least enough to bathe the earlobe. Never use hydrogen or any other peroxide as an antiseptic, soap and salt solution is sufficient.

You will also need some warm water to bathe your ear in before each phase of ear stretching, or alternatively you can take a warm shower first. This softens the ear and helps prevent skin tearing/scarring that could lead to bleeding.

Lastly, you will need some lubricant: avoid Vaseline or any other mineral oil or petroleum-based lubricant. Most advice on piercing stretching recommends emu oil and jojoba, each of which offers mild antiseptic and skin-conditioning properties while also acting as a perfectly adequate lubricant.

Measure earlobes

When drawing holes, the two recommended methods are the taper method and the Teflon method. The taper method involves inserting a tapered rod or pin into the hole, with the narrow end being the same gauge as the hole and the wider end being one gauge down. The size of the cone is that of the desired drilling caliber. So if your piercing is 16g, the decrease will be 14g, with a range of 16g ​​to 14g. These are equivalent to 1.2mm to 1.6mm.

Never use a type more than one step down. However, since drill gauges are always even numbers, one step down is 16g to 14g or 12g to 10g. Also, as the gauge numbers go down, the actual diameter increases. So while 16g is 1.2mm, 10g is 2.4mm.

There are several different types of taper, including a tapered pin on ear jewelry, so simply insert ear jewelry that tapers from your current gauge to the new one. The problem here is that a fully tapered pin will not stretch the ears evenly: the pin must be the same diameter all the way through, or the piercing might also stretch with a taper.

To get past that, you can use an insert rod, which is a tapered rod about 3 inches. After warming the ears with warm water or showering and washing them with antibacterial soap, apply the lubricant to the cone and apply it slowly. Once you reach the thick end, follow it up with earrings in the new size and you’re good to go. Wipe off any excess lubricant and cleanse the ear with antibacterial soap and then a little of the salt solution.

An even safer way is to wrap a layer of non-adhesive Teflon tape around the ear jewelry pin and push it through the lobe. If you can see any gaps when you pull on the ring, then you can do so safely. Wait until the ear has accepted it and then do it again, and so on until you have reached the new size, when you can wear larger earrings.

If there has been severe pain or the piercing is bleeding, you should stop immediately and allow the piercing to heal properly before trying again. If you try to stretch your piercings too soon, before they’ve fully healed, you can tear the skin and even burst, making it difficult to stretch again.

Earlobe Measurement: Aftercare

Aftercare when measuring earlobes is pretty straightforward. It shouldn’t be so much a matter of caring for a piercing until it heals, but rather keeping it clean and re-sizing jewelry from time to time. It is waiting until the ear has accepted the new hole size permanently so that it may be able to change the diameter of the hole once again. Stretched skin should be allowed to thicken and become harder; wait about three times as long as it took for your original piercing to heal. If you want to use a meat tunnel, you can continue to stretch the perforations until the diameter reaches an appreciable size.

If done correctly and the above tips are followed, stretching piercings is safe and relatively easy to do. Many stretch the diameter of their piercings in this way, and measuring the earlobes is probably the most popular form of piercing stretching carried out at the moment. Take your time: Waiting is hard, but if your hearing isn’t ready for the next stretch, it’s likely to be damaged.

Leave A Comment